HomeMedical Tubing Types → TPEs Meet 'Real World' Requirements for Replacing PVC in Tubing

TPEs Meet 'Real World' Requirements for Replacing PVC in Tubing

 

Posted by Brian Buntz to Medical Tubing Types on June 24, 2013

While PVC has long been the material of choice for medical tubing, issues such as those focusing on the phthalate plasticizers used to make PVC flexible are causing some manufacturers to look for alternative materials. Until now the proposed replacements have failed to fully duplicate the advantages of PVC. Teknor Apex Company set out to develop Medalist MD-500 TPEs as the first fully practical alternative to PVC for tubing, providing equivalent or better performance at every stage of production and end use.

Medical tubing shown with connectors. Teknor Apex has developed adhesive systems for bonding its Medalist medical elastomer–based tubing to traditional connectors.

Basics: Flexibility, Clarity, Sterilization Resistance

Medalist TPEs exhibit values comparable to PVC for mechanical properties critical in tubing, such as tensile strength and tensile stress. Their specific gravity is 30% lower, indicating that a pound of TPE yields more linear feet of tubing than a pound of PVC. Here is how they compare in terms of basic functional properties:

  • Flexibility. In PVC compounds this property is the result of high levels of plasticizer—as much as one-third of the formulation by weight. TPEs are inherently elastic.
  • Clarity. Medalist MD-500 compounds provide the same crystal clarity as PVC.
  • Resistance to sterilization. In tests for color shift following heat aging of gamma-irradiated samples, the Medalist compounds proved superior to PVC. Gamma exposure causes degradation of the PVC polymer, resulting in discoloration, embrittlement, and a falloff in mechanical properties. The Medalist compounds even surpassed special gamma-resistant grades of PVC, with heat-aged color shift values less than a third as great.

Everyday Clinical Considerations

Among the greatest failings of previously proposed alternatives to PVC are those involving properties important in daily use by healthcare workers. Medalist MD-500 elastomers have exhibited performance comparable to PVC in:

  • Kink resistance. In many applications, tubing is used for infusion of fluids into the body. If the tube should be bent through a radius that is too tight, it collapses, with consequences that are potentially life-threatening.
  • Clamp resilience. To temporarily halt the flow of liquid, medical tubing is often clamped using either roller or hemostat clamps. Both compress the tube to block flow, and after release of pressure, the tube must recover and allow flow to resume in a short space of time.
  • Necking resistance. Necking is a phenomenon in which the diameter of a tube is permanently reduced when exposed to a longitudinal force.
  • Haptics or ‘feel.’ Most tubing sets are used manually, with the familiar feel of PVC being the accepted norm in the healthcare industry. In blind tests, experienced individuals from the device industry failed to distinguish between PVC and TPE tubing.
Medical tubing shown with connectors. Teknor Apex has developed adhesive systems for bonding its Medalist medical elastomer–based tubing to traditional connectors.

Extrusion and Fabrication

Teknor Apex has worked collaboratively with companies having expertise in medical tubing manufacture. In a demonstration run on a fully equipped, commercial-scale tubing extrusion line, equipment manufacturer American Kuhne Inc. achieved high-speed, tight-tolerance production of tubing from MD-585, an 85 Shore A Medalist compound. The company ran tubing with a 0.105 in. (2.67 mm) OD and 0.020 in. (0.508 mm) wall thickness at speeds up to 830 ft/min (253 m/min.). At a 600 ft/min (183 m/min) line speed, tolerances of +/- 0.0004 in. on the OD and +/- 0.0001 in. on the wall thickness were held.

To demonstrate the capabilities of Medalist MD-500-based tubing in post-extrusion processes, Teknor Apex worked with prominent medical device manufacturers Dunn Industries, Inc., which specializes in medical tubing, and Pelham Plastics Inc., with expertise in assembly techniques. The companies achieved good results in these techniques:

  • Cutting to length. This requires a wide processing window, close tolerances, and ease of cutting in-line with extrusion.
  • Hole punching posed no problems, even allowing for tube rotation producing a serpentine pattern; though this process is typically difficult for elastic materials because of stretching or tearing.
  • Tipping—the process of forming a tapered closure at the end of a tube—was carried out without need for pretreatment or release agents, which would require additional regulatory approvals. Cycles were fast, there was no sticking, tapers were consistent, and the aesthetic quality of the finished product was excellent.
  • Printing was carried out successfully using standard automated corona surface treatment and traditional pad printing with conventional inks. Teknor Apex suggested inks that could be used without the need for pre-treatment.
  • Insert molding, in which luers were applied to the ends of tubing, involved short cycle times, no tube distortion, and excellent bonding of the tubing to pre-colored luers made of either polypropylene or Medalist elastomers.
  • Attachment to standard connectors. Teknor Apex has developed patent-pending bonding systems involving both room temperature-cured and light-cured adhesives, enabling common-size TPE infusion tubing to achieve bonds exhibiting a retention force significantly greater than the minimum required by device manufacturers. In addition, Clean Room Devices LLC has developed an automatic fitting inserter that carries out high-speed assembly of tapered-barb connectors and tubing produced from Medalist MD-500 TPEs.

Elliott Pritikin is senior medical market manager for the Thermoplastic Elastomer Division of Teknor Apex Company.

Related Medical Tubing Types Companies


Eldon James Corp.

Denver, Colorado

Qualifications: ISO 13485, ISO 9001, FDA Registered, Exhibitor in at least 2 MD&M and/or MEDTEC shows, Supplier to Medical Manufacturers

Markets Supplied: North America, Europe, Worldwide

Sunlite Plastics, Inc.

Germantown, Wisconsin

Qualifications: ISO 13485, FDA Registered, Supplier to Medical Manufacturers

Markets Supplied: North America, Europe, Worldwide

NDH Medical Inc.

St. Petersburg, Florida

Qualifications: FDA Registered, CGMP Certified, Exhibitor in at least 2 MD&M and/or MEDTEC shows, Supplier to Medical Manufacturers

Markets Supplied: North America, Europe, Worldwide

Royal Master Grinders, Inc.

Oakland, New Jersey

Related Articles


E-Pro High Performance Hypotube

by Cambus Medical on August 21, 2013

 

E-Pro™ Is an advanced metallurgical solution offering superior kink resistance over traditional ‘304 stainless steel’…

What You Can Visualize, We Can Create

by Tonna Anuligo on August 7, 2013

 

Quality starts with superior manufacturing and processes.

White Paper

by Tonna Anuligo on June 25, 2013

 

Aortic stenosis may be treated with Transcatheter Aortic Valve Replacement (TAVR), a time-saving and less-invasive alternative to…

Smart Catheter Keeps Biofilms at Bay

by Shana Leonard on September 5, 2012

 

Hospital-acquired infections (HAIs) are among the most pressing issues in healthcare today owing to their role in rising costs…

Multilumen Tubing Gets Wired

by Shana Leonard on April 13, 2011

 

While multilumen and wire-reinforced tubes have been used both inside and outside of the medical device arena for many…

Extrusion Process Bumps Catheter Design to the Next Level

by Shana Leonard on March 7, 2011

 

Bump tubing features different diameters at the proximal and distal ends for minimally invasive applications.

Metal Tubing Offers Big 'Draw' for Small Devices

by ucanadmin on March 26, 2010

 

Minimally invasive applications motivate metal tube fabricators to achieve smaller diameters and tighter tolerances.

Combining Material Forces for Composite Tubing

by ucanadmin on January 11, 2009

 

Composite tubing affords flexibility in a multipurpose package for minimally invasive applications.